Balboa Genuine EL2001M3 Spa Circuit Board — G1223 — Current-Production Multi-Pump 240V ML-Series Control System

📥 Downloads & Resources

📄 Balboa EL2001 Mach 3 Tech Sheet — Official PDF — Wiring diagram, DIP switch definitions, setup with 5.5kW heater and 1-speed Pump 2 default

⚡ Balboa Genuine EL2001M3 Spa Circuit Board — G1223 — Current-Production Multi-Pump 240V ML-Series Control System

OEM-quality circuit board for reliable EL2001 Mach 3 spa control and performance.

⚠️ IMPORTANT — PLEASE READ BEFORE ORDERING

• Includes Plug’n’click heater adapter PN 25696. This board ships with the Plug’n’click receptacle adapter already included. If connecting to an existing older screw-terminal heater, you will also need cable adapter PN 25263 (60-138-1040). Removing the copper heater strap is REQUIRED — this prevents arcing that was a known issue with old-style heater straps.
• Identify your board by chip number. The EL2001 Mach 3 board carries chips in the EL2001M3R2 series. Do not order based on appearance alone.
• Replacing a Mach 2.1 board? You will need to move the circuit board standoffs inside the control enclosure — standoff positions differ between Mach 2.1 and Mach 3.
• Circuit boards are non-returnable. Contact Parts4Tubs to confirm your chip number and compatibility before ordering.
• Not for use in a metal enclosure box. Designed for Balboa plastic spa pack enclosures only.

📋 Product Overview

The Balboa Genuine EL2001M3 circuit board (Current MPN G1223) is Balboa Water Group’s latest-production PCB for the EL2001 ML-series spa control platform. It is the current replacement for all legacy EL2001 Mach 1, Mach 2, Mach 2.1, and earlier Mach 3 PCBs (including 53974-05 and all 53974 revisions). This genuine board includes the Plug’n’click heater adapter (PN 25696) — Balboa’s current connector standard, eliminating the older copper strap connection that was prone to arcing.

Built on PCB hardware 22896 Rev B with the EL2001M3 software platform, this board manages a two-speed primary pump, a second pump, a dedicated circulation pump, blower, ozone generator, and spa lighting. The EL2001 platform is characterized by its W15 jumper at J98, enabling the X-B and X-P332 expander board configuration for blower output when operating with a two-speed Pump 2. Optional expander boards expand the system to support additional 2-speed pump outputs.

Compatible with Balboa ML-series topside panels including the ML400, ML551, ML700, and ML900, this board has been deployed across a wide range of spa brands including Master Spas and Bullfrog Spas. It is the direct like-for-like replacement for spas originally equipped with any EL2001 Mach 3 control board.

🌟 Key Features

✅ Genuine Balboa Water Group — Current MPN G1223 — latest-production board, replacing all 53974 series revisions
✅ Includes Plug’n’click Adapter PN 25696 — no separate purchase needed for new heater installations
✅ Eliminates copper strap connection — the new Plug’n’click design prevents arcing at the heater terminal
✅ Two-Speed Pump 1 Control — 240V main jet pump with high and low speed
✅ Pump 2 Output — 240V, configurable 1-speed or 2-speed via DIP switches B1/B2
✅ Blower Output — 240V, 1-speed; with 2-speed Pump 2, X-P332 or X-B expander required
✅ Circulation Pump Output — 240V, separate relay, four programmable filtration modes (A9/A10)
✅ Ozone Generator Output — 120V or 240V field-selectable via W13 wire
✅ Spa Light Output — 12V or 120V selectable via J37 jumper and W9 wire
✅ 5.5kW Heater Support — 240V flow-through heater at full rated output
✅ Expander Board Support — X-P332 (G1920), X-B, X-P, X-P632, X-P231 for additional pump outputs
✅ Dual DIP Switchbanks — Switchbank A (12 positions) and Switchbank B (6 positions)
✅ Persistent Memory (A12) — stores all user preferences, filter settings, and set temperature; battery-free
✅ Real Time Clock (RTC) Support — J91 jumper enables/disables for ML-series panels
✅ Dolphin Remote Compatible — Full-Feature and Spa-Only Dolphin Remote (J20)
✅ M7 Technology — no pressure switch or external sensors required
✅ 1-Year Manufacturer Warranty — backed by Balboa Water Group
✅ Made in the USA — Balboa Instruments, Inc.

⚙️ Technical Specifications

⚠️ Heater wattage note: 5.5kW at 240VAC. At 120V input, heater output is approximately 1/4 of the 240V rated wattage.

ℹ️ US Voltage Note: 240VAC/60Hz US residential service. Do not connect to 50Hz or CE-market power systems.

🔧 Parts and fittings for this

Commonly replaced parts

Parts commonly replaced on this item that we stock.

🔗 Compatibility Guide

⚠️ CRITICAL — IDENTIFY BY CHIP NUMBER: EL2001 Mach 3 chips are in the EL2001M3R2x series. Do not order based on board appearance — EL2000 and EL2001 boards look identical but have different factory configurations (W15 jumper position).

Compatible Topside Panels (ML Series):

Panel Part Number	Panel Name	Capability	J91 Jumper Setting
52684	ML400	Non-time capable	ON (both pins jumpered)
ML551 series	ML551	Time capable	OFF (1 pin only)
52649-01	ML700	Time capable	OFF (1 pin only)
52654-01	ML900	Time capable	OFF (1 pin only)

ℹ️ ML551 compatibility is confirmed via the recommended items listed for this board. ML400, ML700, ML900 are PDF-confirmed.

⚠️ AV/Stereo Note: The EL2001M3 platform includes a J4 connector on the board, and certain system configurations (YCAJ) support stereo at J4. If your original system had a stereo connection through the spa pack, contact Parts4Tubs to confirm AV compatibility for your specific configuration before ordering.

Compatible Expander Boards:

Expander	G-Number	Description	Max Amps	Notes
X-P332	G1920 (PN 55137)	2-relay, 2-speed pump output	12A per relay, 30A fuse	Recommended for G1223 — newer 2-speed expander
X-B	PN 53310	Blower output when P2 is 2-speed	10A fuse	W15 at J98 (EL2001 default)
X-P	PN 53544	1-speed Pump 3 when P2 is 1-speed + Blower on J3	—	W15 to J97
X-P632	PN 53680	2-speed Pump 3; connects to Black AC	30A fuse	Older EL series expander
X-P231	G1910 (PN 53681)	Branch circuit protection, high-amp devices	—	Connects to Black AC
X-O3	PN 53426	Dedicated ozone with X-FOW fiber optic kit	—	Adapter PN 25338 required
X-Mount P	PN 53933	Expander board mounting kit for plastic enclosure	—	—

Replaces / Cross-Reference Part Numbers:

Part Number	Description
G1223	Current Balboa MPN — this board
53974-05	Previous version (no Plug’n’click included)
53974, 53974-01 through 53974-04	All earlier 53974 revisions
53414	EL2001 Mach 2.1
53984	EL2001 variant
54492	EL2001 variant
55013-01	EL2001 variant
54278, 54491, 55022-01	EL2001 variants
55066-04	EL2001 M3 control system (YCAH)
56002-04	EL2001 M3 control system (YCAJ)
54464-04	EL2001 M3 control system (YCAJ)
53882-05	EL2001 M3 system PN using base PCBA 53974-05
33-53974-K	Hydroquip catalog number
600-6292 / 600-6298	OEM system variants
X801095	Master Spas OEM board
X300025	OEM variant
3-60-0097	OEM control system variant
3-70-0808 460 Mach 3	OEM control system variant
EL2001M3R2C, HS2000R2B, MS5000R1A, SPAE15R1A, BF05R2A	Chip numbers replaced

🎛️ Board Functions & Controls

Pump Configuration:

Output	Connector	Voltage	Notes
Pump 1	J1 + W1	240V	2-Speed — heater pump in non-circ setups
Pump 2	J5 + W12	240V	1-Speed default; B1 ON = 1-spd; B1 OFF = 2-spd
Blower	J3 + W2	240V	B3 ON; with 2-speed P2, use X-P332 (G1920) or X-B expander
Circ Pump	J2 + W7	120V or 240V	Separate relay; modes via A9/A10
Pump 3	Via X-P or X-P332	240V	Requires expander board

EL2001 W15 Factory Configuration: The EL2001 board ships with W15 at J98 — this is the X-B/X-P332 expander configuration enabling blower output when Pump 2 is 2-speed. This is the key factory difference from the EL2000 (53834 / G1222) which uses a different W15 position.

Circ Pump Behavior (A9/A10 — PDF-CONFIRMED):

A9	A10	Mode
OFF	OFF	No Circ Pump
ON	OFF	24 Hours
OFF	ON	24 Hr with 3°F Shut-Off
ON	ON	Acts like Pump 1 Low (filter cycles, polls)

Heater Control:

Feature	Specification
Heater Output	5.5kW @ 240VAC
Heater Connection	Plug’n’click (adapter PN 25696 included)
Hi-Limit Sensor	Sensor A (SENS. A)
Temperature Sensor	Sensor B (SENS. B)

Additional Outputs:

Output	Connector	Voltage	Notes
Ozone	J9 + W13	120V or 240V	W13: Red AC = 240V; White AC = 120V
Spa Light	J12 + W9 + J37	12V or 120V	J37 pins 1–2 = 120V; pins 2–3 = 12V; W9 must match
AV / Stereo	J4 + W8	120V	Supported in YCAJ configuration; contact Parts4Tubs to confirm
Fiber / Color Wheel	J12 or J2	—	Via B4 ON; X-FOW kit may be required

DIP Switchbank A (A1–A12 — PDF-CONFIRMED):

Switch	OFF Position	ON Position
A1	Test Mode OFF (normal)	Test Mode ON — technician only
A2	Low Amp — heater off with any HS pump/blower	High Amp — heater on with HS pump/blower
A3	Filter cycles by start/end times	Filter cycles by duration
A4*	12-hour time display	24-hour time display
A5*	Fahrenheit	Celsius
A6	15-min timeout (2 hr for P1 Low)	30-min timeout (4 hr for P1 Low)
A7	No Cleanup Cycle	Cleanup Cycle ON
A8	No ozone suppression	1-hr ozone suppression after pump/blower press
A9	See Circ Pump Table	See Circ Pump Table
A10	See Circ Pump Table	See Circ Pump Table
A11	Non-circ: Ozone with P1 Low; Circ: Ozone with circ (P1 2-spd)	Non-circ: Ozone in filter/cleanup only; Circ: Ozone with circ (P1 1-spd)
A12	Persistent Memory Retained (normal)	Persistent Memory RESET — use at power-up only

A4/A5 defaults apply only when A12 is ON at power-up

DIP Switchbank B (B1–B6 — PDF-CONFIRMED):

Switch	OFF Position	ON Position
B1	Pump 2: 2-Speed	Pump 2: 1-Speed
B2	Pump 2: Disabled	Pump 2: Enabled
B3	Blower: Disabled	Blower: Enabled
B4	Spa Light	Fiber Optic and Color Wheel
B5	Pump 3: Disabled	Pump 3: Enabled
B6	Normal panel layout	Alternate panel layout

Key Jumpers:

Jumper	Function
W15	EL2001 factory position: J98 — enables X-B/X-P332 expander for blower with 2-speed P2
J37	Spa Light voltage: pins 1–2 = 120VAC; pins 2–3 = 12VAC. W9 must match.
J91	RTC: 1 pin = Enabled; pins 1–2 = Disabled (non-time panels)
J83 (CFG)	Logic jumper: NOT installed = DIP switches active
W13	Ozone voltage: Red AC = 240V; White AC = 120V
W9	Spa Light — must match J37 voltage setting

🔧 Installation Requirements

⚠️ Installation must be performed by a licensed electrician in compliance with NEC and all applicable local codes.

Pre-Installation Checklist:

• [ ] Confirm chip number is in the EL2001M3R2x family
• [ ] If replacing Mach 2.1: move standoffs to Mach 3 positions before installing
• [ ] Record all DIP switch settings (A and B banks) on existing board
• [ ] Record all jumper settings (J37, J91, W13, W9, W15)
• [ ] Disconnect all power at the GFCI breaker or disconnect
• [ ] Photograph all wiring and connections
• [ ] Allow capacitors to discharge — 5 minutes after power-off
• [ ] Confirm enclosure is plastic
• [ ] Remove the copper heater strap — this is required, not optional
• [ ] If existing heater has screw terminals: install adapter PN 25263 before connecting to new Plug’n’click receptacle (PN 25696, already included with board)

Electrical Requirements:

Requirement	Specification
Supply Voltage	240VAC / 60Hz
Service	48A, 4-wire (Hot, Hot, Neutral, Ground)
Circuit Breaker	60A maximum
GFCI Protection	Class A GFCI required — NEC Article 680
Ground & Bonding	Required — NEC Article 680
Dedicated Circuit	Required
Disconnect Box	Within line of sight of spa, at least 5 ft from spa walls (NEC)
Wire Type	Copper conductors ONLY
TB1 Torque	27–30 in. lbs.

Key Board Connectors:

Connector	Function
TB1	Main power (Hot/Black, Hot/Red, Neutral/White, Ground)
J1 + W1	Pump 1 (2-Speed)
J2 + W7	Circ Pump (separate relay)
J3 + W2	Blower or Pump 3
J4 + W8	AV / Stereo (always-hot)
J5 + W12	Pump 2 (1- or 2-speed)
J9 + W13	Ozone (120V or 240V)
J12 + W9	Spa Light (12V or 120V)
J20	Dolphin Remote
J37	Spa Light voltage selector
J70/J71/J72	Main topside panel
J83 (CFG)	Logic jumper
J91	Real Time Clock jumper
W15	EL2001 factory: J98
SENS. A / SENS. B	Hi-limit / temperature sensors
VAC	Pressure/vacuum switch input
EXT. RLY	External relay
2SP PUMP 3	2-speed Pump 3 via X-P332/X-P632
AUX. F	Aux freeze sensor

⚠️ Persistent Memory Reset (REQUIRED after any DIP switch or configuration change):

1. Power down the spa
2. Set A12 ON
3. Power up — wait for “GC” or “CG” on panel
4. Set A12 OFF (non-conductive tool if powered, or power down first)
5. If powered down in step 4, power up again
6. Leave A12 OFF for all future power-ups

🛡️ Safety Warnings

• ⚠️ ALWAYS disconnect all power before board work — shock hazard
• ⚠️ Licensed electrician installation; NEC Article 680 compliance mandatory
• ⚠️ Class A GFCI required per NEC Article 680
• ⚠️ Equipment grounding and bonding required per NEC Article 680
• ⚠️ Plastic enclosure ONLY
• ⚠️ Copper heater strap removal is REQUIRED — old-style straps cause arcing; this is a safety issue, not just a preference
• ⚠️ For older heater: install adapter PN 25263 then connect to Plug’n’click PN 25696 (included). Do NOT force old connections onto new connector.
• ⚠️ Reset Persistent Memory (A12) after any DIP switch change — new settings will NOT take effect without this step
• ⚠️ J37 and W9 must be set to the same voltage for spa light
• ⚠️ If replacing Mach 2.1: move standoffs before installation — different positions
• ⚠️ Circuit boards are non-returnable — verify chip number before ordering

---

🔍 Error Codes & Diagnostics

Power-Up Display:

Display	Meaning
Three-number SSID	Software Version (should be 32)
“GC”	Heater 3–6kW range — normal for 240V EL2001
“CG”	Heater 1–3kW range
Priming mode	Normal startup
CFE + switch/jumper	Configuration Error — fix DIP/jumper combo

Common EL-Series Error Messages:

Display	Meaning	Action
OH	Overheat	Allow to cool; check hi-limit sensor
FLO / FL	Flow error	Check pump, filter, sensors
SN / SNA / SNB	Sensor failure	Check Sensor A/B connections
PS	Pressure switch fault	Check pressure switch wiring
CFE	Configuration Error	Fix settings; A12 memory reset

🎯 Ideal Applications

Application	Suitability	Notes
♨️ Any EL2001 Mach 1/2/2.1/3 system	✅ Current-production replacement	Verify EL2001M3R2x chip; move standoffs if Mach 2.1
♨️ Master Spas (MS5000R1A, X801095)	✅ Confirmed	Cross-reference verified
♨️ Bullfrog Spas (BF05R2A)	✅ Confirmed	Cross-reference verified
♨️ Hydroquip EL2001 (33-53974-K)	✅ Confirmed	Same Balboa platform
♨️ ML400 / ML551 / ML700 / ML900 spas	✅ Compatible	All ML-series panels
♨️ Spas with 2-speed P1 + 2-speed P2 + Blower	✅ With X-P332 expander	X-P332 (G1920) handles 2-speed P2 + blower

❓ Frequently Asked Questions

Q: What is the Plug’n’click adapter and do I need anything extra? A: The board ships with Plug’n’click receptacle PN 25696. If your existing heater uses an older screw-terminal connection, you also need cable adapter PN 25263 (60-138-1040, sold separately). The copper heater strap must be fully removed before connecting — this eliminates the arcing risk that was a known problem with older heater connections.

Q: Why was the copper strap removed from the connection design? A: Old-style copper straps were prone to arcing and causing electrical damage over time. The Plug’n’click system provides a secure, vibration-resistant connection that eliminates this issue. Balboa made this change across the VS and EL series control platforms.

Q: How do I confirm this is the right board? A: Check the chip number label on your existing board (white sticker, near center or on relay/transformer). If it shows EL2001M3R2x (any letter suffix), this board is the correct replacement. Contact Parts4Tubs with your chip number if unsure.

Q: My existing board is Mach 2.1 — will this fit? A: The Mach 3 board replaces Mach 2.1 functionally, but you must move the circuit board standoffs inside the enclosure before installation. The mounting hole positions differ between Mach 2.1 and Mach 3 boards.

Q: Does this board support a second 2-speed pump AND a blower? A: Yes, with the X-P332 expander board (G1920). When Pump 2 is configured as 2-speed, the blower requires the X-P332 expander (or X-B expander) with W15 at J98 — which is already the factory setting for this EL2001 board.

Q: Does this board support AV/stereo? A: The EL2001M3 platform includes a J4 AV connector on the board hardware, and certain system configurations support stereo output. Whether your installation supports AV depends on how the original system was wired. Contact Parts4Tubs with your existing board chip number and system information to confirm.

Q: Do I need to reset Persistent Memory after installation? A: Yes, if you change any DIP switch or configuration settings. Set A12 ON at power-up, wait for the ready indicator, then set A12 OFF. Do this before final use.

Q: Is this OEM or aftermarket? A: Genuine Balboa Water Group OEM board (G1223).

Q: What warranty is included? A: 1-year manufacturer warranty. Contact Parts4Tubs for full terms.

⭐ Why Choose the Balboa Genuine EL2001M3 (G1223)

✅ Latest-production Balboa board — G1223 is the current MPN, shipped today
✅ Plug’n’click adapter included — no additional purchase needed for new heater installations
✅ Eliminates arcing risk — Plug’n’click design replaces failure-prone copper strap
✅ Covers all EL2001 Mach generations — replaces Mach 1, 2, 2.1, and Mach 3 boards
✅ Broadest ML-series panel support — ML400, ML551, ML700, ML900 all compatible
✅ Master Spas and Bullfrog compatibility confirmed — covers wide range of spa brands
✅ 1-year manufacturer warranty — Balboa Water Group factory coverage
✅ Non-returnable — Parts4Tubs verifies chip number before you order

🤝 Why Buy from Parts4Tubs

✅ Fast US shipping
✅ Expert technical advice from spa specialists
✅ Competitive pricing
✅ Full warranty support
✅ Compatible expander boards, ML-series topsides, and heater adapter cables available
✅ Help confirming chip number, standoff compatibility, and AV configuration

🔌 Summary

The Balboa Genuine EL2001M3 PCB (G1223) is the current-production replacement for all EL2001 Mach 3 ML-series spa control systems. Rated for 240V/60Hz with a 5.5kW heater, it controls a two-speed primary pump, second pump, blower, circulation pump, ozone, and spa lighting. This board ships with the Plug’n’click heater adapter (PN 25696) — the copper heater strap must be removed, and older heaters need adapter PN 25263. Compatible with ML400, ML551, ML700, and ML900 topsides. Replacing a Mach 2.1 board requires moving the enclosure standoffs. Circuit boards are non-returnable — verify your chip number and confirm your configuration before ordering, and always reset Persistent Memory (A12) after any DIP switch change.

Parts4Tubs is proud to be a Balboa Authorized Online Seller - make sure you only buy genuine Balboa parts from trusted sources.

Finding and identifying a replacement Hot Tub Circuit Board (PCB)

If you are looking to replace a failed PCB on your Hot Tub’s spa pack, then quite often identifying the part that you need can be the hardest thing.

Firstly, you are looking for a model number on the actual circuit board itself. Having the model or serial of your hot tub is not going to help at this point, you need to find the number on the PCB itself.

Now, with certain brands of PCB, the number of the replacement PCB that you need is not going to match identically the one you are replacing. Why is that I hear you ask?

Well, normally, it is an updated version. This means that it might have updated firmware on the PCB or be a later revision. Normally, this means that the part number would be slightly different. This is usually indicated with a “12345678 -x” at the end of that part number where x indicated a firmware revision.

In some cases, there will be some following letters on the part number of the circuit board, “12345678 -x MAS” this can indicate that the PCB was used for an OEM meaning it was produced for a certain hot tub manufacturer and the letters identify the manufacturer.

This means if you source an original PCB, it will not have the letters, but will in most cases work just fine.

It can be confusing I know!

What if you can’t find a model number?

If you can’t find a model number on the PCB itself, then you need to look for a model number on the spa pack. Normally, there is a sticker on the outside of the spa pack that tells you the current ratings and input voltages etc and this will have a model number.

In general, most spa packs in the USA are manufactured by Balboa, Hydro-Quip, ACC or Gecko. I know I am generalising here, but if you have a spa pack that has the brand of your hot tub on, it will be an OEM so the key is identifying who made the original box.

From there, you can normally find an original PCB that you will be able to switch out.

For example, the Balboa VS (value series) is a very popular spa pack that has been used by multiple hot tub manufacturers under their own brand names. Whatever they have called it, strip it back and it is still a Balboa VS.

Visual Inspection

One of the most important things you can do when you are looking for a replacement is to visually inspect the PCB that you have versus the picture online of the replacement you are considering. They need to look the same even if there are the differences in firmware revisions or OEM part numbers, you should be visually replacing a PCB that looks like the one you have.

Configuring a replacement Hot Tub Circuit Board (PCB)

When you get a new PCB, you are more than likely going to need to configure it. Most PCBs have a number of different modes and setups that the can operate in. For this, you will need to manual or spec sheet to guide you.

For things like DIP switches, most of the time you can copy the settings from your original circuit board. You are looking for things like setting the voltage as a lot of PCBs can be configured to run on both 115V and 230V.

You may need to move jumpers or even wires to configure voltages – the key here is that you read the schematic and don’t expect the PCB to just work out of the box – it usually doesn’t.

Troubleshooting a Hot Tub Circuit Board (PCB)

Here are some common things you will see when you replace a PCB on a hot tub.

You press the buttons on the topside control and they don’t control the right parts (pumps or blower etc) – this is a mode configuration thing and you will either need to change some DIP switches on the PCB or an internal or low level programming mode on the topside control. Check the manual for how to do this.

You turn on the hot tub and it trips the breaker – it is not common for a new PCB to fail out of the box (I have not seen one yet!) However, a common mistake is that the voltage has not been set correctly. If it is set for 115V and then you try and turn it on, the current draw will be a lot more (twice) than expected and the breaker will trip.

To check this, unplug all of your kit – heater, pumps, blower and then turn on the PCB. If it trips with nothing plugged in, usually the voltage is incorrectly set and what is happening is that live current is being sent to the ground – because you have 4 wires into the PCB rather than 3. Current on the ground loop causes the trip. Check the settings to make sure it is configures for 230V.

It might not trip until you physically turn on a pump or a blower. As mentioned, if the pack is set to 115V and your pump is meant for 230V, it will draw twice the current at half the voltage and trip your breaker. Check the manual for info on how to set the voltage.