⚙️ Grundfos 43 Series 59896292 Spa Circulation Pump – 230V Single-Speed

Whisper-quiet 230V circulation with seal-free wet rotor technology for reliable spa operation

🔄 Product Overview

The Grundfos 43 Series 59896292 is a 230V single-speed OEM spa circulation pump delivering 12-18 GPM through energy-efficient wet rotor technology. This is the 230V companion to the popular 115V model (59896291), designed for spas wired with 230V dedicated circuits.

Grundfos completely redesigned this 43 Series pump with an ingenious rotating volute that allows installation in virtually any plumbing configuration — simply loosen four screws, rotate the volute to match your existing plumbing, and re-tighten. The 1″ barb inlet and outlet connections accommodate most spa plumbing systems, and optional adapter barbs (1429-131, sold separately) allow conversion to 3/4″ barb for smaller plumbing.

The standout feature of the Grundfos 43 Series is its wet rotor design — the motor rotor runs directly in the pumped liquid, completely eliminating the mechanical shaft seal found in conventional spa circulation pumps. This removes the number one failure point in traditional circ pumps, delivering truly maintenance-free operation. Whisper-quiet and consuming just pennies per day in electricity, this pump runs 24/7 to keep your spa water circulating through the heater and filtration system.

This is a standalone OEM pump — power cord, unions, and fittings are NOT included. For a complete replacement kit with cord, fittings, and 3-speed motor, see the Grundfos Universal Kit (99575701P1 for 115V or 10-0138-KIT for 230V).

✨ Key Features

• ✅ 230V Single-Speed Operation — Designed for 230V dedicated spa circuits, drawing just 0.41A for ultra-low energy consumption
• ✅ 12-18 GPM Flow Rate — Optimal circulation for 24/7 low-flow heater systems and continuous filtration
• ✅ Grundfos 43 Series (UP15-43SPA) — Current production model replacing the earlier UP15-38SPA series
• ✅ Rotating Volute Design — Loosen 4 screws and rotate the volute to any angle to match existing plumbing configurations
• ✅ 1″ Barb Connections — Center suction and side discharge with 1″ barb inlet and outlet (3/4″ adapters available separately)
• ✅ Wet Rotor Technology — NO mechanical shaft seal to leak or replace, eliminating the #1 failure point in conventional circ pumps
• ✅ Whisper-Quiet Operation — Almost silent running ensures no disturbance during spa use
• ✅ Footless Design with Removable Mounts — Compact, lightweight design fits tight equipment compartments
• ✅ Universal Replacement — Direct replacement for Laing E10 230V, previous Grundfos 43 Series models, and compatible HydroQuip pumps
• ✅ 40+ Cross-Reference Part Numbers — Verified replacement for dozens of OEM and aftermarket circulation pump models
• ✅ Grundfos Quality — Backed by one of the world’s most trusted pump manufacturers
• ✅ 1-Year Manufacturer Warranty — Full coverage for peace of mind

🔩 Technical Specifications

Specification	Value
Manufacturer	Grundfos
Series	43 Series
Type Designation	UP15-43SPA (replaces UP15-38SPA)
Primary Part Number	59896292
HydroQuip Part Number	10-0135
UPC	632514098893
Pump Type	Spa Circulation Pump — 24/7 Continuous Duty
Motor Design	Wet Rotor (NO mechanical shaft seal)
Voltage	230V
Frequency	60 Hz
Phase	Single Phase
Amperage	0.41A
Speed	Single Speed
Flow Rate	12-18 GPM
Suction Connection	1″ Barb — Center Suction
Discharge Connection	1″ Barb — Side Discharge
Volute	Rotating — Adjustable to Any Angle (4 screws)
Drain Plug Location	4 O’Clock Position
Mounting	Footless Design with Removable Mounts
Power Cord	NOT INCLUDED — Order Separately
Unions / Fittings	NOT INCLUDED — Order Separately
Warranty	1-Year Manufacturer Warranty

⚡ Electrical Requirements

Electrical Spec	Requirement
Supply Voltage	230V (220V/240V same standard)
Frequency	60 Hz
Phase	Single Phase
Amperage	0.41A
Power Cord	NOT INCLUDED — Order Separately
Wiring	3 Wires: Hot, Hot, Ground (230V — two hot wires, no neutral)

⚠️ CRITICAL — 230V ONLY:

This pump operates on 230V ONLY. Do NOT connect to a 115V circuit. Using the wrong voltage will damage the motor. For 115V spas, order the Grundfos 59896291 instead.

⚠️ CORD NOT INCLUDED:

This is an OEM pump supplied without a power cord. Order a pump cord separately based on your spa’s connector type (AMP, mini-JJ, bare cord, etc.). Connect three wires: hot, hot, and ground.

🔗 Compatibility Guide

59896292 (230V) vs 59896291 (115V) — Grundfos 43 Series Comparison

Feature	59896292 (This Pump)	59896291 (115V Version)
Voltage	230V	115V
Amperage	0.41A	0.74A
Flow Rate	12-18 GPM	12-18 GPM
Connections	1″ Barb	1″ Barb
Speed	Single Speed	Single Speed
Motor Design	Wet Rotor	Wet Rotor
Rotating Volute	Yes	Yes
Cord Included	No	No
HydroQuip Number	10-0135	10-0134

💡 Both pumps are physically identical except for the motor winding voltage. Performance and flow rates are the same. Choose based on your spa’s electrical supply.

Standalone Pump vs Universal Kit

Feature	59896292 (This Pump)	10-0138-KIT (230V Kit)
Type	Standalone OEM Pump	Complete Universal Kit
Speed	Single Speed	3-Speed (Low/Med/High)
Connections	1″ Barb Only	3/4″ Barb + 1″ Adapters
Cord	NOT Included	Included
Unions / Fittings	NOT Included	Included
Mounting Hardware	Removable Mounts	Full Mounting Kit
Best For	Direct replacement — cord/fittings already exist	First-time replacement — need everything

Grundfos 43 Series Family

Model	Voltage	Type	HydroQuip
59896291	115V	Standalone Pump	10-0134
59896292	230V	Standalone Pump (This Pump)	10-0135
99575701P1	115V	Universal Kit (3-Speed)	10-0139-KIT
10-0138-KIT	230V	Universal Kit (3-Speed)	10-0138-KIT

3/4″ Plumbing Conversion

This pump has 1″ barb connections. For spas with 3/4″ plumbing:

• Order 2x Adapter Barbs — Part Number 1429-131 (1″ to 3/4″ conversion, sold separately)
• Order 3/4″ ID Clear Tubing — Part Number 55-270-1513 (50 ft roll) as needed
• Adapters are NOT included with the standalone pump

---

🔩 Alternate Part Numbers & Cross-References

Primary Part Numbers

Part Number	Description
59896292	Grundfos Primary Part Number
10-0135	HydroQuip
10-0135-K	HydroQuip Kit Version
34-430-2055	Horizon Spa & Pool Parts
PUGR1543220S	Grundfos Model Code
UP15-43SPA	Grundfos Type Designation (Current)
632514098893	UPC Code

Grundfos Previous Models (Replaced By 59896292)

Part Number	Notes
1030007	Previous Grundfos 43 Series 230V
59896865	Previous UP15-38SPA Model
UP15-38SPA	Previous Type Designation (Replaced by UP15-43SPA)
242011500	Previous Grundfos Model
UP15-20	Older Grundfos Circulation Pump
UP1520	Older Grundfos Circulation Pump
PMPUP1538SPA230	Previous Model Code
PMPUP1538S230V	Previous Model Code (Alternate)
PMPUP1520S230V	Previous Model Code
GG92009	Previous Grundfos

HydroQuip Cross-References

Part Number	Notes
10-0121	HydroQuip Circ Pump
10-0122	HydroQuip Circ Pump
10-0123	HydroQuip Circ Pump
10-0125	HydroQuip Circ Pump
10-0134	HydroQuip (115V Version)
10-0135	HydroQuip (230V — This Pump)
10-0135-K	HydroQuip Kit Version
LHB07100138	HydroQuip Internal Code
LHB07100140	HydroQuip Internal Code
LHB07100142	HydroQuip Internal Code

Laing Cross-References

Part Number	Notes
E10-NSHN2W-20	Laing E10 230V
E10-NSTN2W-20	Laing E10 230V Variant
6050U0010	Laing E10 230V 3/4″ Barb (With Adapters)
6050U0014	Laing E10 230V 3/4″ Barb + Cord
6050U0016	Laing E10 230V
74079	Laing E10 230V
73979	Laing 230V
73999	Laing 230V

Sundance / Jacuzzi Cross-References

Part Number	Notes
6000-125	Sundance/Jacuzzi Circ Pump
6509	Sundance/Jacuzzi
6510	Sundance/Jacuzzi
6917	Sundance/Jacuzzi
6918	Sundance/Jacuzzi
6920	Sundance/Jacuzzi
6921	Sundance/Jacuzzi
6974	Sundance/Jacuzzi
69750	Sundance/Jacuzzi
610688	Sundance/Jacuzzi

Other Brand Cross-References

Part Number	Brand / Notes
1-P107GF1B24	Industry Cross-Reference
404034	Industry Cross-Reference
92009	Industry Cross-Reference
9333-02	Industry Cross-Reference
PU602394	Hurricane Spa Pump
733886739794	UPC Cross-Reference
733886739992	UPC Cross-Reference
733886740790	UPC Cross-Reference

---

🛠️ Installation Requirements

What’s in the Box

• ✅ Grundfos 59896292 Circulation Pump
• ✅ Removable Mounting Brackets
• ❌ Power Cord — NOT INCLUDED (Order Separately)
• ❌ Unions / Fittings — NOT INCLUDED (Order Separately)
• ❌ 3/4″ Barb Adapters — NOT INCLUDED (Order 1429-131 if Needed)

Mounting

Requirement	Specification
Mounting Position	Horizontal — Motor must remain dry
Base	Solid, level surface
Location	Sheltered — Protected from frost, rain, direct sun, and dust
Ventilation	Adequate airflow around motor housing
Access	Sufficient clearance for service and maintenance

Plumbing

Connection	Size
Suction	1″ Barb — Center
Discharge	1″ Barb — Side
Volute Adjustment	Loosen 4 screws, rotate to desired position, re-tighten
For 3/4″ Plumbing	Order 2x Adapter Barbs 1429-131 + Tubing 55-270-1513

Installation Notes

⚠️ Power cord NOT INCLUDED — order separately based on your spa’s connector type. Connect three wires: hot, hot, and ground (230V — no neutral wire).

⚠️ Pump must be installed below water level (flooded suction) to operate properly.

⚠️ Rotating volute — loosen the 4 volute screws, rotate to match your plumbing configuration, then re-tighten securely.

⚠️ GFCI protection is required by the National Electrical Code (NEC) for all hot tub and spa installations.

⚠️ Install in a sheltered location — protect from frost, rain, direct sunlight, and dust to maximize pump life.

⚠️ 230V ONLY — verify your spa’s voltage before ordering. For 115V, order 59896291.

---

🔧 Maintenance Guide

Routine Maintenance

Task	Frequency	Notes
Check for leaks	Monthly	Around barb connections and hose clamps
Inspect hose clamps	Monthly	Tighten if needed
Check flow rate	Monthly	Reduced flow indicates blockage
Inspect mounting brackets	Quarterly	Tighten if loose
Verify quiet operation	Quarterly	Unusual noise indicates bearing wear
Clean intake screen	As Needed	Remove any debris blocking suction

Warning Signs — Replace Pump If:

• Unusual noise (grinding, humming, rattling)
• Motor overheating excessively
• Reduced or no water flow
• Motor trips breaker repeatedly
• Pump fails to start

Wet Rotor Advantage — NO Seal Replacement Needed

Unlike conventional spa circulation pumps (Gecko CMHP, Waterway Iron Might, Balboa) that use a mechanical shaft seal which eventually leaks and requires replacement, the Grundfos 43 Series uses a wet rotor design where the motor rotor runs directly in the pumped liquid. This eliminates the #1 failure point in traditional circ pumps — there is NO shaft seal to leak, wear out, or replace. This is a truly maintenance-free pump design.

🎯 Ideal Applications

Application	Suitability	Notes
♨️ 24/7 Spa Circulation	✅ Yes — Primary Use	Continuous duty low-flow heater circulation
♨️ Low-Flow Heater Systems	✅ Yes — Primary Use	12-18 GPM optimal for spa heaters
♨️ Replacement Existing Grundfos 43 Series 230V	✅ Yes — Direct Replacement	Same pump, updated model
♨️ Replacement Laing E10 230V (1″ Barb)	✅ Yes — Direct Replacement	Verified cross-reference
♨️ Replacement Laing E10 230V (3/4″ Barb)	✅ Yes — With Adapters	Order 2x 1429-131 adapter barbs
♨️ Replacement HydroQuip 10-0135	✅ Yes — Same Pump	HydroQuip-branded Grundfos
♨️ Sundance / Jacuzzi 230V Spas	✅ Yes	Verified OEM replacement
♨️ Replacement Waterway Tiny Might 230V (1″ Barb)	✅ Yes	Compatible replacement
🛁 Adjustable Flow Needed	❌ No — Single Speed	Use Grundfos 10-0138-KIT for 3-speed 230V
🛁 1-1/2″ MBT Plumbing	❌ No	Use Gecko Aqua-Flo CMHP for 1-1/2″ connections
🛁 115V Spa	❌ No — 230V Only	Use Grundfos 59896291 for 115V

❓ Frequently Asked Questions

Q: What is the amperage draw of this pump? A: The SpaGuts authorized listing specifies 0.41A at 230V/60Hz. Some retailers list 0.74A, which appears to be the 115V version’s amperage. At 230V, 0.41A is consistent with the same wattage at double the voltage.

Q: What is the flow rate? A: 12-18 GPM, designed for continuous 24/7 spa circulation through low-flow heater systems.

Q: Does this pump come with a power cord? A: No. This is an OEM pump supplied without a cord. Order a pump cord separately based on your spa’s connector type. At 230V, connect two hot wires and one ground wire — there is no neutral.

Q: What size are the connections? A: 1″ barb inlet (center suction) and 1″ barb outlet (side discharge). For spas with 3/4″ plumbing, order 2x adapter barbs (1429-131) sold separately.

Q: Does this replace the Laing E10 230V? A: Yes. The Grundfos 59896292 is a verified direct replacement for the Laing E10 230V models including E10-NSHN2W-20, E10-NSTN2W-20, 6050U0010, 6050U0014, 6050U0016, and 74079.

Q: What is the difference between this pump (59896292) and the 59896291? A: The only difference is voltage. The 59896292 operates on 230V (0.41A), while the 59896291 operates on 115V (0.74A). Both deliver the same 12-18 GPM flow rate with identical physical dimensions and connections. Choose based on your spa’s electrical supply.

Q: What is the difference between this standalone pump and the Universal Kit? A: This standalone pump (59896292) is single-speed with 1″ barb connections and does NOT include a cord, fittings, or adapters. The Universal Kit (10-0138-KIT for 230V) is a 3-speed pump with a complete plumbing package including cord, unions, fittings, elbows, 3/4″ and 1″ barb adapters, and mounting hardware. The standalone pump is best when cord and fittings already exist from a previous pump. The kit is best for first-time replacements needing everything.

Q: Does this pump have a shaft seal that needs replacing? A: No. The Grundfos 43 Series uses a wet rotor design where the motor rotor runs in the pumped liquid. There is NO mechanical shaft seal to leak, wear out, or replace. This eliminates the number one failure point found in conventional spa circulation pumps.

Q: Can I rotate the volute to match my plumbing? A: Yes. Loosen the 4 volute screws, rotate the volute to the desired position to match your existing plumbing, then re-tighten securely. This allows installation in virtually any plumbing configuration.

Q: What voltage does this pump require? A: 230V/60Hz ONLY (also referenced as 220V or 240V — same standard). Do NOT connect to a 115V circuit. Using the wrong voltage will damage the motor. For 115V, order 59896291 instead.

Q: Is this pump quiet? A: Yes, extremely. The Grundfos 43 Series is renowned for almost silent operation — you may not even notice it running. The wet rotor design contributes to the exceptionally quiet performance.

Q: Does this pump include unions or fittings? A: No. This is an OEM standalone pump with removable mounting brackets only. Order unions, fittings, and hose clamps separately as needed for your installation.

Q: Does this replace 40+ part numbers? A: Yes. The Grundfos 59896292 is a verified replacement for over 40 part numbers across Grundfos, HydroQuip, Laing, Sundance/Jacuzzi, and other manufacturers. See the full cross-reference table above.

Q: Do I need a GFCI breaker? A: Yes. GFCI protection is required by the National Electrical Code (NEC) for all hot tub and spa installations.

Q: What warranty is included? A: 1-year manufacturer warranty. Contact Parts4Tubs for full warranty terms and support

🏆 Why Choose the Grundfos 43 Series 59896292

• ✅ Wet Rotor Design — NO mechanical shaft seal to leak or replace, eliminating the #1 failure point in conventional spa circulation pumps
• ✅ Whisper-Quiet Operation — Almost silent running for undisturbed spa enjoyment
• ✅ Ultra-Low Energy Consumption — Just 0.41A at 230V, costs pennies per day to operate 24/7
• ✅ Rotating Volute — Adjustable to any angle, fits virtually any plumbing configuration without replumbing
• ✅ 12-18 GPM Flow Rate — Optimal circulation for low-flow heater systems
• ✅ Compact, Lightweight Design — Fits tight equipment compartments with footless removable mounts
• ✅ Direct Laing E10 230V Replacement — Verified cross-reference, same mounting footprint
• ✅ 40+ Verified Cross-References — Replaces dozens of OEM and aftermarket models across major brands
• ✅ Maintenance-Free Motor — Wet rotor design requires no seal replacement throughout pump life
• ✅ Grundfos Quality — Backed by one of the world’s most trusted pump manufacturers with decades of proven reliability
• ✅ 1-Year Manufacturer Warranty — Full coverage for peace of mind

🤝 Why Buy from Parts4Tubs

• ✅ US-based support for American customers
• ✅ Fast shipping across the United States
• ✅ Expert advice from spa and hot tub specialists
• ✅ Competitive pricing in USD
• ✅ Full warranty support
• ✅ Hassle-free returns
• ✅ 3/4″ adapter barbs and tubing available
• ✅ Dedicated customer service team

✨ Summary

The Grundfos 43 Series 59896292 is a 230V single-speed spa circulation pump delivering 12-18 GPM through proven wet rotor technology that eliminates the need for shaft seal maintenance. Featuring an innovative rotating volute, 1″ barb connections, and whisper-quiet operation, this pump is a verified replacement for 40+ part numbers across Grundfos, Laing, HydroQuip, Sundance/Jacuzzi, and other major brands. A reliable, energy-efficient choice for 24/7 spa circulation backed by Grundfos quality and a 1-year warranty. Order from Parts4Tubs today for fast shipping and expert support.

How do I Replace a Hot Tub Pump?

Here's a general step-by-step guide on how to replace a hot tub pump. Keep in mind that the specific steps may vary depending on your hot tub's make and model, so it's essential to consult your hot tub's manual for model-specific instructions. If you're not comfortable with this procedure, it's a good idea to seek professional assistance.

Materials You'll Need:

• Replacement pump
• Pipe wrench
• Adjustable wrench
• Screwdriver
• Pipe sealant (thread tape or plumber's putty)
• PVC primer and cement (if you have PVC plumbing)
• Teflon tape (for threaded connections)

Procedure:

1. Turn Off the Power: Before you begin, ensure the hot tub's power supply is turned off at the circuit breaker or disconnect switch. Safety should always be a priority when working with electrical components.

2. Drain the Hot Tub: If your hot tub is not already empty, you'll need to drain it. Follow your hot tub's manual or manufacturer's instructions for proper draining. (You might not need to do this if you can lock the pump off with the gate valves)

3. Locate the Pump: Identify the location of the existing pump in your hot tub. It's usually located near the equipment area or in a designated pump compartment.

4. Disconnect the Electrical Wiring: Carefully disconnect the electrical wiring from the old pump. This typically involves removing the electrical conduit cover, unscrewing wire nuts, and disconnecting the wires from the terminals. Be sure to note the wire connections or take a picture for reference when connecting the new pump.

5. Disconnect the Plumbing: Depending on your hot tub's plumbing setup, you'll need to disconnect the plumbing connections to the pump. Use a pipe wrench or adjustable wrench to loosen and remove the fittings. Be prepared for some water spillage when disconnecting the plumbing.

6. Remove the Old Pump: Once the electrical and plumbing connections are detached, carefully remove the old pump from its mounting position. Some pumps may be secured with mounting brackets or bolts.

7. Prepare the New Pump: If the new pump is not pre-assembled, you may need to attach fittings, unions, or adapters to match your hot tub's plumbing. Ensure that you use the appropriate sealant or Teflon tape on threaded connections to prevent leaks.

8. Mount the New Pump: Position the new pump in the same location as the old one and secure it in place using the mounting brackets or bolts.

9. Reconnect Plumbing: Reconnect the plumbing to the new pump, ensuring that all connections are tight and secure. If your hot tub uses PVC plumbing, use PVC primer and cement to bond the connections properly.

10. Reconnect Electrical Wiring: Reconnect the electrical wiring to the new pump, following the notes or pictures you took earlier. Make sure all wires are properly connected and secure.

11. Turn On the Power: Restore power to the hot tub by switching on the circuit breaker or reconnecting the disconnect switch.

12. Test the Pump: Turn on the hot tub's pump to ensure that it's working correctly. Check for any signs of leaks or irregularities in the plumbing connections.

13. Refill the Hot Tub: Once you've confirmed that the new pump is functioning properly, refill the hot tub with water.

14. Check for Leaks: Inspect the plumbing connections for any leaks. If you find any, turn off the pump, drain the tub again, and reseal the connections as needed.

15. Monitor: Keep an eye on the pump and plumbing for the next few days to ensure everything is functioning correctly and that there are no further issues.

Remember that this is a general guideline, and the specific steps may vary based on your hot tub's design. If you're unsure or uncomfortable with any aspect of this process, please do get in touch, happy to help.

How do I know what size hot tub pump I have?

Determining the size of your hot tub pump is an important step when it comes to maintenance or replacement. To find out the size of your hot tub pump, follow these steps:

1. Check the Manual: The easiest way to determine the size of your hot tub pump is to consult the owner's manual or user documentation that came with your hot tub. The manual typically contains detailed information about the specifications and components of your hot tub, including the pump.

2. Look at the Pump Housing: If you don't have access to the manual or it doesn't provide the information you need, inspect the pump itself. Most hot tub pumps have a label or plate on the pump housing that displays essential details, including the pump's model number, manufacturer, and specifications. You can then send that to me or Google it.

3. Measure the Pump: If the label is missing or damaged, you can measure the pump's dimensions. Measure the diameter of the pump's wet end (the part where the water flows) and the length of the wet end. These measurements can help identify the size and capacity of the pump.

4. Consult the Manufacturer: If you can't find the information on the pump or in the manual, contact the hot tub manufacturer or a reputable dealer. Provide them with your hot tub's model and serial number, and they should be able to identify the correct pump size for your specific hot tub.

5. Online Research: You can also search online using the pump's model number or hot tub's make and model. Many manufacturers provide detailed information about their products on their websites, and you may find specifications for your pump model.

Once you have determined the size and specifications of your hot tub pump, you can proceed with maintenance, repairs, or replacement if necessary. Keep in mind that replacing a hot tub pump with the same size and capacity as the original is crucial to ensure proper water circulation and filtration in your hot tub. If you're unsure about any aspect of this process, get in touch, always happy to help.