💧 Waterway Executive 56 Spa Pump (3722021-1D) — 5.0 HP 2-Speed 230V

Precision-engineered for powerful hydrotherapy jets and efficient filtration

♨️ Product Overview

The Waterway Executive 56 (Model 3722021-1D) is a high-performance 5.0 HP dual-speed jet pump built for demanding hot tub and spa installations. Manufactured by Waterway Plastics in the USA, the Executive 56 series combines a purpose-engineered wet end with a heavy-duty 56-frame motor, delivering intense jet pressure on high speed (3450 RPM) and energy-saving filtration on low speed (1725 RPM).

This model features matched 2 inch suction and 2 inch side discharge ports with Male Buttress Thread (MBT) connections — the standard plumbing configuration for the majority of residential hot tubs. The 6-1/2 inch diameter wet end generates superior head pressure for multi-jet configurations, while the 2 inch intake maintains efficient water flow and reduced operating noise. Constructed with silicone carbide seals, Viton bellows, and a 316 stainless steel seal casing, the 3722021-1D delivers lasting corrosion resistance in chlorine, bromine, and salt water systems.

Note: This pump does NOT include unions or power cord — these must be purchased separately. If your existing pump has a 2-1/2 inch suction port, you need the 3722021-13 model instead.

✨ Key Features

✅ 5.0 HP Dual-Speed Motor — High speed at 3450 RPM for powerful massage jets; low speed at 1725 RPM for quiet, energy-efficient filtration

✅ Matched 2 Inch Ports — Both suction and discharge are 2 inch MBT, the most common port configuration for residential hot tub replacement

✅ 56-Frame Motor Construction — Larger frame provides added strength, cooler operating temperatures, and longer motor life versus 48-frame motors

✅ 6-1/2 Inch Diameter Wet End — Oversized wet end generates higher head pressure for demanding multi-jet spa systems

✅ Silicone Carbide Seal with Viton Bellows — PS1100 seal assembly with 316 stainless steel casing resists chlorine, bromine, and salt corrosion

✅ Dual Double-Shielded Ball Bearings — Moisture-resistant grease provides quieter operation and extended bearing life

✅ Split Capacitor (Start and Run) — Reduces energy consumption during motor operation

✅ Thermal Overload Protection — Automatic motor protection prevents overheating and extends motor life

✅ Four Sets of Insulated Windings — Dual-speed motors feature four winding sets for increased operational efficiency

✅ 90-Degree Wet End Rotation — Discharge can be repositioned every 90 degrees for flexible installation in any equipment compartment

✅ Made in the USA — Designed, engineered, and manufactured by Waterway Plastics in Oxnard, California

📊 Technical Specifications

Specification	Detail
Model Number	3722021-1D
Updated Model Number	PF-40-2N22M (replaces PF-50-2N22C)
Manufacturer	Waterway Plastics
Pump Type	Jet Pump (Executive 56 Series)
Motor Power	5.0 HP
Speed Settings	Dual Speed (2-Speed)
High Speed RPM	3450 RPM
Low Speed RPM	1725 RPM
Voltage	230V
Frequency	60 Hz
Phase	Single Phase
High Speed Amperage	16.4A
Low Speed Amperage	4.8A
Frame Type	56Y Frame
Wet End Diameter	6-1/2 inches
Suction (Intake) Port	2 inches MBT (actual thread OD: approximately 3 inches)
Discharge Port	2 inches MBT (actual thread OD: approximately 3 inches)
Discharge Location	Side Discharge
Suction Location	Center
Wet End Rotation	Every 90 degrees
Seal Type	PS1100 — Silicone carbide seals, Viton bellows, 316SS casing
Bearings	Dual double-shielded ball bearings with moisture-resistant grease
Capacitor	Split capacitor (start and run)
Thermal Protection	Yes — Automatic overload protection
Dimension “A” (Motor Length)	10.375 inches
Weight	47 lbs
Cord Included	No — Power cord not included
Unions Included	No — Unions not included
Self-Priming	No — Must be installed below water level (flooded suction)
Country of Origin	USA

---

🔌 Electrical Requirements

Electrical Spec	Requirement
Supply Voltage	230V
Frequency	60 Hz
Phase	Single Phase
Full Load Amps (High Speed)	16.4A
Full Load Amps (Low Speed)	4.8A
Minimum Circuit Breaker	25A (recommended — consult licensed electrician for load calculation)
Wire Size	Consult licensed electrician per NEC requirements

⚠️ IMPORTANT ELECTRICAL SAFETY INFORMATION:

All electrical work must be performed by a licensed electrician in accordance with the National Electrical Code (NEC) and local building codes. Hot tubs and spas require GFCI (Ground Fault Circuit Interrupter) protection. A dedicated circuit is required — do not share with other appliances.

⚠️ 2-SPEED WIRING WARNING: Do NOT wire both speeds to run simultaneously. When removing the power cord from your existing pump, mark your wires for “common,” “high speed,” and “low speed” before disconnecting. The wiring diagram is located on the motor nameplate or terminal cover.

⚠️ VOLTAGE CHECK: Be sure to check the motor voltage on your existing pump — not the voltage supplied to the spa — to determine the correct replacement pump voltage. Applying incorrect voltage will damage the motor and void the warranty.

---

🔄 Compatibility Guide

Frame and Port Identification

Specification	This Pump
Frame Type	56 Frame
Wet End	6-1/2 inch diameter
Suction (Intake)	2 inch MBT (center)
Discharge	2 inch MBT (side)
Discharge Position	Side (rotatable every 90 degrees)

3722021-1D vs. 3722021-13 — What’s the Difference?

These are both 5.0 HP 2-speed Executive 56-frame pumps with identical electrical specifications (16.4/4.8 amps, 230V/60Hz). The only difference is the port configuration:

Feature	3722021-1D (This Pump)	3722021-13
Suction (Intake)	2 inches (thread OD: ~3 inches)	2-1/2 inches (thread OD: ~3-5/8 inches)
Discharge	2 inches (thread OD: ~3 inches)	2 inches (thread OD: ~3 inches)
Weight	47 lbs	46 lbs

Measure the outside diameter of your existing pump’s threaded connections to determine which model you need. If the suction thread OD measures approximately 3-5/8 inches, you need the 3722021-13 instead.

How to Identify Your Pump’s Thread Size

Hot tub pump plumbing sizes are nominal — not the actual outside diameter. Measure the outside diameter of the threaded connection to confirm:

Nominal Size	Actual Thread OD
1-1/2 inch	Approximately 2-3/8 inches
2 inches	Approximately 3 inches
2-1/2 inches	Approximately 3-5/8 inches

How to Select the Correct Replacement Pump

Choosing a pump based on Horsepower (HP) alone can lead to selecting the wrong pump. HP ratings on spa pumps may be listed as SPL-HP, BHP, MBHP, RHP, or S-HP, which differ from continuous operating horsepower. Some spa manufacturers relabel this pump as 6 HP or even 7 HP. Instead, match these specifications from your existing pump:

1. Confirm whether you have a 48-frame or 56-frame motor
2. Match the high-speed amperage rating on the pump label
3. Confirm suction and discharge port sizes (measure the thread OD)
4. Verify voltage (115V vs. 230V)

⚠️ Do NOT upgrade from a 48-frame to a 56-frame pump — this can overpower your spa and cause damage to plumbing, jets, and the spa shell.

Alternate Part Numbers and Cross-References

This pump (3722021-1D) is also referenced under the following part numbers:

• PF-50-2N22C
• PF-45-2N22C
• PF-40-2N22M
• PF-50-2N22M
• PF-50-2N22F
• 1-00-0219
• 34-270-3598
• WW37220211D
• WWP-10-1423
• 37220211D
• 1-P250E52024
• P250E52024
• 3722021-0306
• 3722021-0D86
• 3722021-0T7GDY
• 3722021-OD8
• 3M22021
• 5039-510
• 625252
• 722021
• 372202A-1D

Compatible Applications

This pump fits a wide range of hot tub and spa brands including spas by Dynasty (part 12600), Infinity Spas (Aquastorm), and many others. It is commonly used as an OEM and replacement pump across multiple manufacturers. Always verify frame type, amperage, and port sizes before ordering.

---

🛠️ Installation Requirements

Mounting

Requirement	Specification
Mounting Position	Horizontal — Must be installed below water level (flooded suction)
Base	Solid, level surface with adequate floor drainage
Ventilation	Ensure adequate airflow around motor for cooling
Access	Allow sufficient clearance for maintenance and future pump removal
Moisture Protection	Installation area should be clear of direct water spray

Plumbing Connections

Connection	Size	Type
Suction (Intake)	2 inches	Male Buttress Thread (MBT) — Center
Discharge	2 inches	Male Buttress Thread (MBT) — Side
Union Type	Waterway tailpiece assemblies recommended	Hand tighten only — do NOT use wrenches

Installation Notes

⚠️ Pump must be installed below water level — this pump is NOT self-priming

⚠️ Never run the pump dry — causes seal damage and may result in scalding hot water buildup inside the pump housing

⚠️ Install shut-off valves on both inlet and outlet for future maintenance

⚠️ Hand tighten unions only — do NOT use a wrench or adhesives

⚠️ Use only Teflon tape or sealing compounds approved for use with plastic — do NOT use pipe dope, as some pipe dopes cause stress cracking of plastic parts

⚠️ The wet end discharge can be rotated every 90 degrees by loosening the four motor thru-bolts

⚠️ Ensure proper grounding and bonding per NEC requirements

⚠️ GFCI protection is required by code for all hot tub and spa installations

⚠️ Pressure testing during installation should not exceed 40 PSI

Product Change Notification

Waterway has updated the Executive wet end configuration. The two side drain plug ports have been removed to streamline production. Only the main bottom drain port remains. If side ports are required for your installation, they can be drilled and tapped on-site.

---

⚙️ Maintenance Guide

Routine Maintenance

Task	Frequency	Notes
Check for leaks	Monthly	Inspect around seal area, unions, and plumbing connections
Inspect unions	Monthly	Hand tighten if needed — never use a wrench
Clean strainer/filter	As needed	Remove debris to maintain proper flow
Check motor amperage	Annually	Should be within 10% of nameplate rating (16.4A high / 4.8A low)
Inspect motor vents	Quarterly	Keep clear of debris for proper cooling airflow
Check mounting security	Quarterly	Tighten mounting if loose to reduce vibration and noise
Inspect for air leaks	As needed	Air bubbles in return lines indicate suction-side air leak

Warning Signs — Replace Pump If:

• Unusual noise (grinding, screeching, or rumbling)
• Water leaking from the shaft seal area
• Motor trips the circuit breaker repeatedly
• Reduced water flow or jet pressure
• Motor overheating or shutting down on thermal protection
• Motor hums but will not start
• Amperage draw exceeds 10% of nameplate rating

Seal Replacement

Specification	Detail
Seal Model	PS1100
Seal Material	Silicone carbide faces, Viton bellows, 316 stainless steel casing
Chemical Resistance	Chlorine, bromine, and salt water

⚠️ Replace the seal at the first sign of water leakage from the seal area. Continued operation with a leaking seal will damage the motor bearings and windings.

---

🎯 Ideal Applications

Application	Suitability	Notes
♨️ Hot tub jet pump	Yes	Primary application — delivers powerful jet pressure for multi-jet configurations
♨️ Spa jet pump	Yes	Ideal for high-performance spa systems requiring maximum flow through 2 inch plumbing
🛁 Whirlpool bath	Yes	Can be used with whirlpool bath systems if appropriately marked
♨️ Dual-speed filtration	Yes	Low speed provides energy-efficient filtration at 1725 RPM
♨️ Commercial spa systems	Yes	56-frame construction suited for commercial-grade applications

---

💬 Frequently Asked Questions

Q: What horsepower is this pump? A: This pump is rated at 5.0 HP by Waterway. However, some spa manufacturers relabel this pump as 6 HP or even 7 HP using different HP rating methods (SPL-HP, BHP, etc.). The most reliable way to confirm you are selecting the correct replacement is to match the high-speed amperage (16.4A for this model) and frame size (56 frame) rather than relying solely on the HP number.

Q: Will this fit my hot tub? A: This pump has a 56-frame motor with 2 inch suction (center) and 2 inch side discharge using Male Buttress Thread connections. To confirm compatibility, check your existing pump’s frame type, amperage rating, and port sizes. If your current pump has a 2-1/2 inch suction port, you need the 3722021-13 model instead.

Q: What voltage does this pump require? A: 230V / 60Hz single phase. All electrical installation must be performed by a licensed electrician. Using incorrect voltage will damage the motor and void the warranty.

Q: Does this pump run on 115V or 230V? A: This specific model (3722021-1D) is 230V only. Always verify the voltage on your existing pump’s motor nameplate — check the motor voltage, not the voltage supplied to the spa panel.

Q: Is this a single or dual speed pump? A: This is a dual-speed (2-speed) pump. High speed runs at 3450 RPM (16.4A) for jet operation. Low speed runs at 1725 RPM (4.8A) for filtration and circulation. It can also be wired for single-speed operation if needed.

Q: What size are the ports? A: Both suction (intake) and discharge are 2 inches MBT. The nominal 2 inch size measures approximately 3 inches outside diameter at the threads. This is the most common port configuration for residential hot tubs.

Q: Does this pump come with a power cord and unions? A: No. This pump does NOT include a power cord or unions. These must be purchased separately. For 2-speed pumps, a 4-wire AMP cord is typically required.

Q: What is the difference between this pump (3722021-1D) and the 3722021-13? A: Both are identical 5.0 HP 2-speed Executive 56-frame pumps with the same electrical specifications. The only difference is the suction port size: this pump (3722021-1D) has a 2 inch suction, while the 3722021-13 has a 2-1/2 inch suction. Measure your existing pump’s suction thread OD to determine which you need.

Q: My old pump says 6 HP or 7 HP — is this the right replacement? A: Possibly. Some spa manufacturers relabel Waterway’s 5.0 HP pump with higher HP numbers using different rating methods. Do not rely on the HP number alone. Instead, match the high-speed amperage (16.4A), frame type (56 frame), port sizes (2 inch x 2 inch), and voltage (230V) to confirm this is the correct replacement.

Q: What warranty is included? A: Waterway provides a manufacturer warranty. Warranty terms require registration with Waterway at the time of purchase — contact Parts4Tubs for current warranty details and registration assistance.

Q: How do I know if my pump needs replacing? A: Signs that your pump needs replacement include unusual noise (grinding, screeching), water leaking from the seal area, reduced jet pressure, the motor repeatedly tripping the breaker, the motor overheating or shutting off, or the motor humming but not starting.

Q: Do I need a GFCI breaker? A: Yes, GFCI (Ground Fault Circuit Interrupter) protection is required by the National Electrical Code (NEC) for all hot tub and spa installations. This is a critical safety requirement.

Q: Can I rotate the discharge direction? A: Yes. The wet end can be rotated every 90 degrees by loosening the four motor thru-bolts. The pump ships with the discharge in the factory default position (12 o’clock). It can be repositioned to 3, 6, or 9 o’clock orientations.

Q: What does the “C” or “M” in the PF model number mean? A: The last letter indicates the motor brand used. “C” references Century/A.O. Smith brand motors; “M” references U.S. Motors. Both deliver the same performance specifications, and the motor brand does not need to be matched when selecting a replacement. Waterway reserves the right to change motor brands without notice.

📥 Downloads and Resources

📄 48/56 Frame Executive, EX2 & Viper Pump Instructions (PDF) — Installation guide, wiring instructions, troubleshooting, and exploded parts view

🏆 Why Choose the Waterway Executive 56 (3722021-1D)

✅ Maximum Jet Power — 5.0 HP motor at 16.4 amps delivers intense hydrotherapy performance for multi-jet spa configurations

✅ Standard 2 Inch Ports — Matched 2 inch suction and discharge fit the majority of residential hot tub plumbing without adapters

✅ Energy-Efficient Dual Speed — Low-speed filtration at 4.8 amps significantly reduces electricity costs compared to full-speed operation

✅ Premium Seal System — Silicone carbide seals with Viton bellows and 316SS casing resist corrosion from chlorine, bromine, and salt water systems

✅ Quiet Operation — Dual double-shielded ball bearings with moisture-resistant grease and efficient wet end design reduce operational noise

✅ American Quality — Designed, engineered, and manufactured in the USA by Waterway Plastics in Oxnard, California

🤝 Why Buy From Parts4Tubs

✅ US-based support for American customers

✅ Fast shipping across the United States

✅ Expert advice from spa and hot tub specialists

✅ Competitive pricing

✅ Full warranty support

✅ Hassle-free returns

✅ Replacement seals, unions, and AMP cords available

✅ Dedicated customer service team

🌟 Summary

The Waterway Executive 56 (3722021-1D) is a 5.0 HP dual-speed jet pump with matched 2 inch suction and discharge ports — the standard configuration for most residential hot tubs. Running at 16.4/4.8 amps on 230V with a robust 56-frame motor, this American-made pump delivers powerful jet performance through a 6-1/2 inch wet end with superior head pressure and a premium PS1100 seal assembly. The rotatable wet end, side discharge design, and proven Executive series engineering make it a reliable, direct-fit replacement for high-performance spa systems. Available now at Parts4Tubs with expert support and fast US shipping.

Showing 1 – 5 of 5 results Showing all 5 results Showing the single result No results found

Sort by Price low to high

Sort by Popularity

Sort by Rating

Sort by Price low to high

Sort by Price high to low

Sort by Newness

Sort by Name A - Z

Sort by Name Z - A

Filters Sort results

Reset Apply

	Magic Plastics Union 0602-15 (1.5″ Pump Union) | 1-1/2″S x 1-1/2″FBT Union, Pump, Magic, 1-1/2"S x 1-1/2"FBT (Industry Standard) w/ O-Ring	$6.36 Max: 575 Min: 1 Step: 1 Add to cart
	Magic Plastics Union 0602-20 (2″ Pump Union) | 2″S x 2″FBT w/ O-Ring Union, Pump, Magic, 2"S x 2"FBT (Industry Standard) w/ O-Ring	$8.00 Max: 491 Min: 1 Step: 1 Add to cart
	Waterway Union 400-6010 | 2-1/2″ Union Nut with 2-1/2″ Slip tailpiece and o-ring (2.5″ union) Union, Pump, Waterway, 2-1/2"FBT x 2-1/2"S	$14.77 Max: 145 Min: 1 Step: 1 Add to cart
	1 Speed Pump / Blower / AMP Cord | 21086 Amp Plug, Pump, 1-Speed, 14/3, 4-Pin, 5' Cord, White	$24.71 Max: 426 Min: 1 Step: 1 Add to cart
	Balboa Amp Plug 21087 (For 2 Speed Pumps) Amp Plug, Pump 1 (2-Speed) 14/4, 72" Long, White	$31.72 Max: 172 Min: 1 Step: 1 Add to cart

Hot Tub Pump Collar & Union Size Chart

Imperial & Metric Specifications

Union Size	Collar Size	Thread OD	Union OD	O-Ring Size
1.5" Female Buttress Thread (FBT)	2.5" / 64mm (Tip to Tip) Measurement	2-1/2" 64mm	2-13/16" 71mm	2-5/16" OD 59mm
2" Female Buttress Thread (FBT)	3.1" / 78mm (Tip to Tip) Measurement	3-1/16" 78mm	3-3/8" 81mm	2-15/16" OD 75mm
2.5" Female Buttress Thread (FBT)	3.6" / 91mm (Tip to Tip) Measurement	3-5/8" 91mm	4-1/4" 108mm	3-7/16" OD 87mm

Important Notes

The union "size" (1.5", 2", 2.5") is nominal and doesn't correspond to any actual measurement.

Collar size is measured from thread tip to thread tip on the pump outlet.

Most hot tub pumps use Female Buttress Thread (FBT) - 98% of applications.

O-ring gaskets may vary between manufacturers - measure your existing gasket for accuracy.

How do I Replace a Hot Tub Pump?

Here's a general step-by-step guide on how to replace a hot tub pump. Keep in mind that the specific steps may vary depending on your hot tub's make and model, so it's essential to consult your hot tub's manual for model-specific instructions. If you're not comfortable with this procedure, it's a good idea to seek professional assistance.

Materials You'll Need:

• Replacement pump
• Pipe wrench
• Adjustable wrench
• Screwdriver
• Pipe sealant (thread tape or plumber's putty)
• PVC primer and cement (if you have PVC plumbing)
• Teflon tape (for threaded connections)

Procedure:

1. Turn Off the Power: Before you begin, ensure the hot tub's power supply is turned off at the circuit breaker or disconnect switch. Safety should always be a priority when working with electrical components.

2. Drain the Hot Tub: If your hot tub is not already empty, you'll need to drain it. Follow your hot tub's manual or manufacturer's instructions for proper draining. (You might not need to do this if you can lock the pump off with the gate valves)

3. Locate the Pump: Identify the location of the existing pump in your hot tub. It's usually located near the equipment area or in a designated pump compartment.

4. Disconnect the Electrical Wiring: Carefully disconnect the electrical wiring from the old pump. This typically involves removing the electrical conduit cover, unscrewing wire nuts, and disconnecting the wires from the terminals. Be sure to note the wire connections or take a picture for reference when connecting the new pump.

5. Disconnect the Plumbing: Depending on your hot tub's plumbing setup, you'll need to disconnect the plumbing connections to the pump. Use a pipe wrench or adjustable wrench to loosen and remove the fittings. Be prepared for some water spillage when disconnecting the plumbing.

6. Remove the Old Pump: Once the electrical and plumbing connections are detached, carefully remove the old pump from its mounting position. Some pumps may be secured with mounting brackets or bolts.

7. Prepare the New Pump: If the new pump is not pre-assembled, you may need to attach fittings, unions, or adapters to match your hot tub's plumbing. Ensure that you use the appropriate sealant or Teflon tape on threaded connections to prevent leaks.

8. Mount the New Pump: Position the new pump in the same location as the old one and secure it in place using the mounting brackets or bolts.

9. Reconnect Plumbing: Reconnect the plumbing to the new pump, ensuring that all connections are tight and secure. If your hot tub uses PVC plumbing, use PVC primer and cement to bond the connections properly.

10. Reconnect Electrical Wiring: Reconnect the electrical wiring to the new pump, following the notes or pictures you took earlier. Make sure all wires are properly connected and secure.

11. Turn On the Power: Restore power to the hot tub by switching on the circuit breaker or reconnecting the disconnect switch.

12. Test the Pump: Turn on the hot tub's pump to ensure that it's working correctly. Check for any signs of leaks or irregularities in the plumbing connections.

13. Refill the Hot Tub: Once you've confirmed that the new pump is functioning properly, refill the hot tub with water.

14. Check for Leaks: Inspect the plumbing connections for any leaks. If you find any, turn off the pump, drain the tub again, and reseal the connections as needed.

15. Monitor: Keep an eye on the pump and plumbing for the next few days to ensure everything is functioning correctly and that there are no further issues.

Remember that this is a general guideline, and the specific steps may vary based on your hot tub's design. If you're unsure or uncomfortable with any aspect of this process, please do get in touch, happy to help.

How do I know what size hot tub pump I have?

Determining the size of your hot tub pump is an important step when it comes to maintenance or replacement. To find out the size of your hot tub pump, follow these steps:

1. Check the Manual: The easiest way to determine the size of your hot tub pump is to consult the owner's manual or user documentation that came with your hot tub. The manual typically contains detailed information about the specifications and components of your hot tub, including the pump.

2. Look at the Pump Housing: If you don't have access to the manual or it doesn't provide the information you need, inspect the pump itself. Most hot tub pumps have a label or plate on the pump housing that displays essential details, including the pump's model number, manufacturer, and specifications. You can then send that to me or Google it.

3. Measure the Pump: If the label is missing or damaged, you can measure the pump's dimensions. Measure the diameter of the pump's wet end (the part where the water flows) and the length of the wet end. These measurements can help identify the size and capacity of the pump.

4. Consult the Manufacturer: If you can't find the information on the pump or in the manual, contact the hot tub manufacturer or a reputable dealer. Provide them with your hot tub's model and serial number, and they should be able to identify the correct pump size for your specific hot tub.

5. Online Research: You can also search online using the pump's model number or hot tub's make and model. Many manufacturers provide detailed information about their products on their websites, and you may find specifications for your pump model.

Once you have determined the size and specifications of your hot tub pump, you can proceed with maintenance, repairs, or replacement if necessary. Keep in mind that replacing a hot tub pump with the same size and capacity as the original is crucial to ensure proper water circulation and filtration in your hot tub. If you're unsure about any aspect of this process, get in touch, always happy to help.