Motor, Nidec/US Motor, 1.5hp, 115/230v, 1-Spd, 48Yfr, SQFL | ASQ225
$340.23
| Manufacturer part number | ASQ225 |
| UPC (GTIN) | 786382123055 |
| Warranty | 1 year manufacturer warranty |
| Returns | 30-day returns – see our returns policy |
Out of stock
Want to be notified when this product is back in stock?
Fast dispatch
Order in
--:--:--
for shipping today
⚠️ Energy regulations: please read
Since 29 September 2025, US Department of Energy rules have required newly made replacement pool pump motors of 1.15 to 5 total horsepower to be variable speed. This is a single-speed motor. Motors built before that date can still be sold and installed until stock runs out, so supply of this motor will end.
Some states, including California, have stricter rules that may not allow a single-speed replacement. Check your local regulations before ordering.
A variable-speed motor also costs much less to run. Our variable-speed square flange motors: Neptune 1.65 THP, 115/230V · Neptune 2.25 THP, 230V. Check the mounting and total horsepower against your pump before ordering.
Pumps and replacement motors that are single speed and one (1) TOTAL HP or greater cannot be sold, offered for sale, or installed in a residential pool for filtration use in California, Title 20 CCR sections 1601-1609.
| Motor Type | Pool |
| Motor Amperage | 19.0A/9.5A |
| voltage | 115v/230v |
| Phase | 1 Phase (1ph) |
| Frame Type | 48Y |
| Speed | 1 Speed (1-Spd) |
| Horsepower | 1.5hp |
| Total Horsepower | 2.25thp |
| Motor Shaft Type | Threaded |
| Motor Style | Square Flange |
| Manufacturer | Nidec-Motor-Corp/US-Motors |
U.S. Motors (Nidec) replacement pool pump motor – 1-1/2 HP, 115V / 230V, single speed, 48Y frame
⚙️ What this motor is
This is a replacement motor only, not a complete pump. It is a square flange motor, which you can recognise by a square plate on the pump end with a bolt through each corner. It is a 48Y frame motor. It runs on 115V / 230V, single speed. It bolts to the wet end you already have, so the pump housing, impeller and plumbing stay where they are.
✅ Check these before you order
- Compare total horsepower, not nameplate horsepower. Multiply the horsepower on your old motor’s label by the service factor next to it, and compare that figure. This motor is rated 1-1/2 HP.
- Mounting. Square flange, C-face and thru-bolt motors are not interchangeable and there is no adapter between them, so check yours matches before ordering.
- Frame size. Measure across the round body of the motor: roughly 5-1/2 to 5-7/8 inches is a 48 frame, roughly 6-1/2 to 6-3/4 inches is a 56 frame. Measuring beats reading the old label, because some makers labelled 48 frame motors as 56. This one is a 48Y frame.
- Voltage. This motor is 115V / 230V. Read it off the old motor’s label rather than assuming from the wiring – a spa wired for 240V can still run a 120V pump.
🔧 When you fit it
- Fit a new shaft seal at the same time. A failed shaft seal lets water into the motor and is the most common reason a motor dies. Reusing the old one on a new motor is the quickest way to ruin it.
- Rotation. Pool and spa motors turn counter-clockwise seen from the shaft end, shown on the label as CCW or CCWPE. They cannot be reversed by swapping wires, so check the old label if it says anything different.
- Keep the horsepower the same unless you are changing the impeller too – the impeller is matched to the motor’s output.
🔩 Technical specifications
| Specification | Value |
|---|---|
| Manufacturer part number | ASQ225 |
| UPC | 786382123055 |
| Brand | U.S. Motors (Nidec) |
| Horsepower | 1-1/2 HP |
| Speed | 1-speed |
| Voltage | 115V / 230V |
| Frequency | 60 Hz |
| Current draw | 19.0 A at 115V / 9.5 A at 230V |
| Phase | Single phase |
| RPM | 3,450 RPM |
| Motor frame | 48Y frame |
| Frame dimensions | 48Y frame, 5-1/2 in frame diameter, 5/8 in threaded shaft (1/2-20 UNF-2A) |
| Mounting style | Square flange |
Find the right pump or motor
Enter what is printed on the label of the one you are replacing. Anything that differs is shown with the difference spelled out, so you can judge it for yourself.
Port size is the plumbing thread, not the pipe — a 2 inch union measures about 3 inches across the male thread. Amps are compared to within half an amp, since published figures round differently between motor brands. Voltage is never treated as a near miss: a 115V motor is not one step from a 230V supply. Anything whose page does not publish a figure you entered is left out rather than offered with a caveat — search it by name to see it anyway.
🔧 Parts and fittings for this
| Part | Our part number | Availability | Price | ||
|---|---|---|---|---|---|
 |
Tool, Seal Setting | SS2136 | 9 in stock | $103.11 | Add to cart |
 |
Tool, Pool Tool, Armature Holding | 128 | 29 in stock | $32.88 | Add to cart |
 |
Tool, Pool Tool, Impeller Wrench, Closed | 127 | 13 in stock | $53.79 | Add to cart |
| Hpart # | 35-184-1725 |
|---|---|
| Brand | Nidec Motor Corp/US Motors |